Skip to content

THE COURSE / M1 THE SWITCH / M1.5

The MOSFET

After this lesson you can:

  • Explain how the gate turns the channel between source and drain on and off.
  • Read a transistor's curves: the linear and saturation regions, threshold, on-current and off-current.
  • Use the subthreshold swing to work out leakage, and say why CMOS uses so little power.

Loading the lesson…

Sources

  1. C. C. Hu, Modern Semiconductor Devices for Integrated Circuits (Pearson, 2010), chapter 6, "MOS Transistor" (free from the author). Two PN junctions, the source and drain, supply and drain the carriers; the gate turns the inversion layer on and off through the oxide: a field-effect transistor, off (Ioff) or on (Ion); shallow trench isolation around it. Lilienfeld's 1930 patent and Heil's 1935 patent described field-effect devices. NFET: N+ source and drain in a P body, on when Vg = Vdd; PFET the opposite; the junctions are never forward-biased. CMOS: in either static state one transistor is off and no current flows from Vdd to ground, so CMOS circuits use much less power; N wells made in the P substrate for the PFETs. At small Vds the transistor acts as a resistor; the current saturates beyond Vdsat as the channel pinches off at the drain end, like a stream feeding a waterfall. Idsat ∝ (W/L) Cox µ (Vgs − Vt)². The PFET is made about twice as wide as the NFET, as holes are less mobile. Inverter delay ≈ CVdd/4 × (1/IonN + 1/IonP): speed needs Ion. Dynamic power = kCVdd²f.
  2. C. C. Hu, Modern Semiconductor Devices for Integrated Circuits (Pearson, 2010), chapter 7, "MOSFETs in ICs—Scaling, Leakage, and Other Topics" (free from the author). Gate oxide thinned from 300 nm at the 10 µm technology to 1.2 nm at 65 nm, roughly in proportion to the line width, to raise the on-current and to control Vt roll-off as the channel shortens. Below 1.5 nm, tunnelling leakage limits it: 1.2 nm of SiO₂ leaks 10³ A/cm², 10 A from 1 mm² of gate, enough to drain a phone's battery in minutes; nitrogen cuts it about tenfold. HfO₂ has k ≈ 24, six times SiO₂'s: 6 nm of HfO₂ gives the capacitance of 1 nm of SiO₂ (an EOT of 1 nm) with leakage several orders of magnitude lower; a thin SiO₂ interfacial layer under it; metal gates, two metals for N and P transistors. SiO₂ breakdown about 7 MV/cm for ten years' operation. Below threshold the current falls exponentially, by ten for every S = η × 60 mV at room temperature (η ≥ 1; e.g. 90 mV at η = 1.5): the subthreshold swing. Vt is defined where Ids = 100 nA × W/L (some companies 200 nA); Ioff, at Vgs = 0, = 100 nA × (W/L) × 10^(−Vt/S). An Ioff of 100 nA per transistor across a hundred million transistors is 10 A in standby. Vt can't be made arbitrarily small; S is lowered by a thinner oxide or a wider depletion layer. Vt rolls off as the channel shortens: short-channel transistors leak more. Moore (1965): devices per chip double every 18 to 24 months; each node shrinks features to 70%, halving the area of a circuit, every two to three years. Table 7–1 (history and ITRS projection): 90 nm (2003) Vdd 1.2 V, 65 nm 1.1, 45 nm 1.0, 32 nm 1.0, 22 nm (2013) 0.9 V; strained silicon from 90 nm, high-k/metal gate from 45 nm, immersion lithography at 32 nm, a new structure at 22 nm. Strain: SiGe grown in trenches beside a PFET's gate compresses its channel and raises hole mobility. Vt roll-off: in a short channel the drain lowers the source–channel barrier (drain-induced barrier lowering), so less gate voltage is needed; roll-off ∝ (Vds + 0.4 V) e^(−L/ld), ld ∝ (Toxe Wdep Xj)^(1/3); minimum L several times ld. Even with a thin oxide the drain controls leakage paths below the surface, far from the gate: ultra-thin bodies and multigate transistors remove them. Random dopant fluctuation: the number and place of dopant atoms in a small transistor varies, and with it Vt. Designers get two or three Vts to choose from.