Skip to content

THE COURSE / PILOT

How chips are made, one short lesson at a time.

Narrated slides and diagrams, five minutes each, with questions that come back later so they stick. The pilot is M5, deposition; the other thirteen modules follow its format.

M12

The fab as a system

What does it take, around the tools, to make chips day and night?
  1. M12.1

    The fab as a system

    The four levels; clean air, utilities, wafers and people; cleanroom classes by area.

    Start the lesson
  2. M12.2

    The cleanroom

    ISO classes; people as the main source; downflow, air changes and pressure; gowning; minienvironments.

    Start the lesson
  3. M12.3

    Utilities

    Ultrapure water, gases, chemicals, power, cooling and exhaust, and what is treated before it leaves.

    Start the lesson
  4. M12.7

    Cooling

    At POWER 2's chiller hall: a tool's heat out through four loops; chillers, COP and N+1; the towers.

    Start the lesson
  5. M12.8

    Power

    At the main substation: grid to tool, voltage dips and riding through, then run the dip.

    Start the lesson
  6. M12.4

    Moving wafers

    FOUPs and load ports; overhead transport and stockers; the MES and dispatch.

    Start the lesson
  7. M12.5

    Safety

    Toxic, pyrophoric and corrosive gases; gas cabinets, detection and abatement; alarms and evacuation.

    Start the lesson
  8. M12.6

    Keeping it running

    Maintenance, availability and OEE; cycle time, work in progress and Little's law.

    Start the lesson
  9. M12 ✎

    Run the bay

    Choose how busy a bay of tools runs, how its breakdowns fall and how many lots jump the queue, and watch the lots wait.

    Open the interactive
  10. M12 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M1

The switch

How does a sliver of silicon become a switch, and why did the switch change shape?
  1. M1.1

    Conductor, insulator, semiconductor

    The silicon crystal; electrons in bands; the band gap; why a metal conducts, the oxide insulates and silicon does a little.

    Start the lesson
  2. M1.2

    Electrons and holes, and doping

    Donors and acceptors; n-type and p-type; n × p = ni²; mobility and resistivity.

    Start the lesson
  3. M1.3

    The p–n junction

    The depletion region and the built-in voltage; forward and reverse bias; the diode's curve.

    Start the lesson
  4. M1.4

    The gate: the MOS capacitor

    Accumulation, depletion and inversion; the threshold voltage; thinner oxides, then high-k.

    Start the lesson
  5. M1.5

    The MOSFET

    The channel; the transistor's curves; on-current, off-current, threshold and subthreshold swing; CMOS.

    Start the lesson
  6. M1.6

    Scaling and its limits

    Dennard scaling and its end; short channels; leakage; strain and high-k metal gates.

    Start the lesson
  7. M1.7

    FinFET to nanosheet

    The gate on three sides, then four; stacked nanosheets; what each shape costs to make.

    Start the lesson
  8. M1 ✎

    Turn it on

    Choose a transistor's threshold, its gate length and its shape, predict its leak, and sweep its gate: three missions, then your own.

    Open the interactive
  9. M1 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M2

Pure silicon

How does sand become a wafer pure, flat and perfect enough to build chips on?
  1. M2.1

    From sand to polysilicon

    Quartz to metallurgical silicon, trichlorosilane distilled, and polysilicon grown on hot rods.

    Being written
  2. M2.2

    Growing the crystal

    The Czochralski puller: seed, neck, shoulder, body and tail; the dopant, the oxygen, the magnet, and float zone.

    Start the lesson
  3. M2.3

    From ingot to wafer

    Cropped, ground round and notched, sliced by wire, edges rounded, ground flat and etched.

    Start the lesson
  4. M2.4

    A flat, clean wafer

    Polished, cleaned, inspected and sealed in its box.

    Start the lesson
  5. M2.5

    Engineered wafers

    Epitaxy, anneals and silicon on insulator.

    Start the lesson
  6. M2.6

    Beyond silicon: SiC and GaN

    Wide band gaps for power and radio, and the slow, hard crystals behind them.

    Start the lesson
  7. M2.7

    The metals you can't see

    Trace metals on and in the wafer: the droplet, the vapour etch, the ICP-MS, the TXRF and the air.

    Start the lesson
  8. M2.8

    Where the water goes

    The plant's used water, treated by stream: neutralised, fluoride taken down with lime, sludge pressed, water reused or checked before the sea.

    Start the lesson
  9. M2.9

    Where the heat goes

    A puller's heater power, carried off in its cooling water, through the plate exchangers, the chillers and the cooling towers to the air.

    Start the lesson
  10. M2 ✎

    Grow the ingot

    Melt, seed, neck and grow a crystal in a cutaway puller: predict each change, then see it, chapter by chapter, to the wafer you would order.

    Open the interactive
M3

Design to mask

How does an idea for a chip become the masks a fab prints?
  1. M3.1

    Architecture

    What the chip is for, its blocks, and its budgets for area, power and speed; why a bigger array lost to more bandwidth.

    Start the lesson
  2. M3.2

    RTL and verification

    Hardware described in code, simulated, covered and formally checked, then synthesised to a netlist; why random tests miss rare bugs.

    Start the lesson
  3. M3.3

    IP and the PDK

    The blocks a team licenses, the foundry's process design kit, and why a layout belongs to one process.

    Start the lesson
  4. M3.4

    Physical design to tape-out

    Floorplan, placement, clock tree and routing; why long wires are slow; signoff and what tape-out hands the fab.

    Start the lesson
  5. M3.5

    Masks and OPC

    Why the mask is not the layout: OPC and inverse lithography, mask writing and inspection, and what a mask set costs.

    Start the lesson
  6. M3 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M4

Patterning

How is a pattern far smaller than light's wavelength printed on a wafer, layer after layer, in the right place?
  1. M4.1

    Print, then transfer

    The patterning loop; projection and reduction; CD = k1·λ/NA; the wavelengths; depth of focus.

    Start the lesson
  2. M4.2

    Resist and the track

    Priming, spin coating and bakes; chemically amplified resist and its acid; contrast; standing waves.

    Start the lesson
  3. M4.3

    A flat, clean back

    The focus budget; a particle under the wafer becomes a defocused spot; backside cleaning.

    Start the lesson
  4. M4.4

    DUV immersion

    193 nm light through water: NA 1.35; step and scan; alignment, levelling and corrections.

    Start the lesson
  5. M4.5

    EUV

    13.5 nm light from a tin plasma; multilayer mirrors and a reflective mask, in vacuum.

    Start the lesson
  6. M4.6

    Few photons, and High-NA

    Shot noise and stochastic defects; dose against throughput; 0.55 NA and what it gives up.

    Start the lesson
  7. M4.7

    More than one exposure

    Litho-etch twice and its overlay; spacers that halve and quarter the pitch; cuts.

    Start the lesson
  8. M4.8

    Strip and rework

    A downstream plasma strip, the residue clean, and redoing a layer before the etch.

    Start the lesson
  9. M4 ✎

    Print the line

    Choose a scanner, its light, a way to pattern and a dose, and see what prints a layer: one exposure, spacers, and EUV with its photons.

    Open the interactive
  10. M4 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M5

Deposition

Which film, which method?
  1. M5.1

    Films

    A transistor and its wiring as a stack of films, and the properties each can't do without.

    Start the lesson
  2. M5.2

    CVD

    Gases react on a hot surface; growth limited by the reaction or by the gas reaching it.

    Start the lesson
  3. M5.3

    PECVD

    A plasma supplies the energy instead of heat, so films grow below what the wiring survives.

    Start the lesson
  4. M5.4

    Atomic layer deposition

    Two self-limiting halves a cycle: even inside a deep trench, and slow.

    Start the lesson
  5. M5.5

    PVD

    Sputtering: atoms knocked off a target fly in straight lines; overhang and voids.

    Start the lesson
  6. M5.6

    Epitaxy

    A crystal grown on a crystal, beside the gate, to strain the channel.

    Start the lesson
  7. M5.7

    Plating, and choosing

    Copper fills from the bottom up; then the module's question, answered for six films.

    Start the lesson
  8. M5 ✎

    Fill the trench

    Pick a method, predict, and watch the film grow: three missions, then your own trench.

    Open the interactive
  9. M5 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M6

Etch, clean and CMP

What comes off, and what must stay?
  1. M6.1

    Taking material away

    Etch, strip, clean and polish; straight down or every way at once; what an etch uses up.

    Start the lesson
  2. M6.2

    Plasma etch

    Ions and radicals together cut straight down; the chemistry, the deep hole and the endpoint.

    Start the lesson
  3. M6.3

    Profile and selectivity

    Cutting a gate in steps, and stopping on a layer a few nanometres thick; trims and fins.

    Start the lesson
  4. M6.4

    Atomic layer and selective etch

    Etching a layer at a time, and removing one material from between nanosheets.

    Start the lesson
  5. M6.5

    Strip and clean

    Resist off by plasma; particles, metals and oxide off by chemistry; drying without collapse.

    Start the lesson
  6. M6.6

    CMP

    Slurry and pad flatten the wafer; dishing, erosion and the endpoint.

    Start the lesson
  7. M6.7

    Choosing

    The module's question answered: four questions, and the method for each job.

    Start the lesson
  8. M6 ✎

    Etch to the stop

    Choose the gas, the ion energy and the overetch that open a contact without punching its stop: three missions, then your own.

    Open the interactive
  9. M6 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M7

Doping and heat

How do you put dopant atoms exactly where they belong, and keep them there?
  1. M7.1

    Doping and heat

    Where a transistor's dopants go; diffusion or implantation; heat repairs and moves; √(Dt) and the thermal budget.

    Start the lesson
  2. M7.2

    Ion implantation

    The beamline, the dose counted as charge, range and straggle, channeling and the tilt.

    Start the lesson
  3. M7.3

    Deep wells

    MeV ions from a linear accelerator, retrograde wells, and how thick a mask must be.

    Start the lesson
  4. M7.4

    Source and drain

    Heavy doses at low energy: milliamp beams, amorphous silicon and its regrowth.

    Start the lesson
  5. M7.5

    Diffusion and the spike anneal

    Fick's laws, activation, transient enhanced diffusion, and why anneals got shorter.

    Start the lesson
  6. M7.6

    Thermal oxidation

    Dry and wet oxide, the Deal–Grove model, and the batch furnace.

    Start the lesson
  7. M7.7

    A millisecond of heat, and choosing

    Heating only the surface; the module's question answered for each doping step.

    Start the lesson
  8. M7 ✎

    Place the junction

    Choose the energy, the dose, the tilt and the anneal that put a dopant where it belongs: a well, a halo and an extension, then your own.

    Open the interactive
  9. M7 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M8

Integration

How do the steps fit together into one working transistor and its wiring?
  1. M8.1

    One flow, front to back

    Transistors, contacts, wiring; the four steps nanosheets add; the gate goes in last.

    Start the lesson
  2. M8.2

    The stack and the fin

    Silicon channels and silicon-germanium placeholders, grown cool; fins, isolation and the sub-fin beneath.

    Start the lesson
  3. M8.3

    The temporary gate and the inner spacers

    A dummy gate, the source/drain recess, and the inner spacers between gate and source.

    Start the lesson
  4. M8.4

    Source, drain, and the gate at last

    In-situ doped source and drain, the channels released, high-k and metal round every sheet.

    Start the lesson
  5. M8.5

    Contacts and the first wiring

    Contacts aligned to the gate, silicide, and the tightest wiring level.

    Start the lesson
  6. M8.6

    Power from the back: the bond

    Why power moves to the backside, and the wafer flipped onto a carrier.

    Start the lesson
  7. M8.7

    Thin to the transistors, and power from below

    Grind, polish and etch to the stop; contacts and rails from beneath.

    Start the lesson
  8. M8 ✎

    Build the transistor

    Put a flow's steps in order: a FinFET, a nanosheet transistor and nanosheets powered from the back, then your own.

    Open the interactive
  9. M8 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M9

Measure and yield

How does a fab know each step worked, and find out why when one didn't?
  1. M9.1

    Measure, then decide

    Metrology, inspection and electrical test; variation in time and space; sampling, feedback, and whether a gauge is good enough.

    Start the lesson
  2. M9.2

    Film thickness by light

    Two reflections interfering; a spectrum fitted to a model; reflectometry and ellipsometry; the wafer map.

    Start the lesson
  3. M9.3

    Critical dimensions

    The CD-SEM: edges in secondary electrons, low landing energy, and what biases a width.

    Start the lesson
  4. M9.4

    Overlay

    Layer on layer: targets, imaging and diffraction, and the correction sent back to the scanner.

    Start the lesson
  5. M9.5

    Finding defects

    Whole-wafer optical inspection, die against die, and what it can and can't tell.

    Start the lesson
  6. M9.6

    From defects to yield

    Review and classification, killer defects, and yield from defect density and die size.

    Start the lesson
  7. M9.7

    Control charts and the parametric test

    Test structures in the scribe line, Shewhart charts, and Cp and Cpk.

    Start the lesson
  8. M9.8

    Failure analysis

    From a failing die to its cause: localisation, an ion-beam cross-section, a lamella for the TEM.

    Start the lesson
  9. M9 ✎

    Yield and the die

    Choose a die's size, a point in the ramp and a split into chiplets, and count the good dies on a wafer, at random or clustered.

    Open the interactive
  10. M9 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
M10

Memory

Why is DRAM built the way it is, how does a die with failing bits still ship, and how are dies stacked into HBM?
  1. M10.1

    One transistor, one capacitor

    The DRAM cell: a bit as charge; reading drains it, so it's written back; leakage, and refresh every 64 ms.

    Start the lesson
  2. M10.2

    The buried word line

    The cell's transistor buried below the silicon, and the four tools that build it.

    Start the lesson
  3. M10.3

    The capacitor

    A cylinder tens of nanometres wide and many times as tall, lined with high-k.

    Start the lesson
  4. M10.4

    Sense, test and repair

    Wafer test, spare rows and columns, and the laser that swaps them in.

    Start the lesson
  5. M10.5

    Through-silicon vias, thinning and reveal

    Why DRAM is stacked; the via from etch to copper; each die ground thin until the vias show.

    Start the lesson
  6. M10.6

    Stacking: MR-MUF

    Tack the dies, join every bump at once, fill and mould the stack; against film, and hybrid bonding next.

    Start the lesson
  7. M10.7

    Testing the stack

    Known-good dies, a test port through the base die, spare lanes, and the heat that limits height.

    Start the lesson
  8. M10 ✎

    Repair the array

    A die's failing bits and its few spare rows and columns: cover them all with the fewest spares, or say it can't be saved. Three missions, then your own die.

    Open the interactive
  9. M10 ✎

    Build the stack

    How tall a stack of DRAM dies, and how they're joined, against its yield and its heat; then find the bad connection on a stack's test map. Three missions, then your own stack.

    Open the interactive
  10. M10 ✓

    Module check

    Ten questions across the module's seven lessons, eight to pass; then practise its exam scenarios.

    Take the check
M11

Package and test

How does a sorted wafer become a part that ships, and how did packaging become where the accelerator is made?
  1. M11.1

    From wafer to die: thin and cut

    The sort map; grinding thin, tape and frame; blade, laser groove and stealth dicing; only the good dies picked.

    Start the lesson
  2. M11.2

    Die attach and wire bond

    A die glued to its frame, a wire welded from every pad, moulded, marked and sawn.

    Start the lesson
  3. M11.3

    Bumps and flip chip

    Copper pillars plated in thick resist, capped with solder; the die flipped onto its substrate and underfilled.

    Start the lesson
  4. M11.4

    Did it survive? Package test and reliability

    Final test and binning, burn-in, X-ray and ultrasound, and dry pack.

    Start the lesson
  5. M11.5

    Chiplets on an interposer

    Why one big die became many: logic and HBM side by side on silicon, built chip-on-wafer.

    Start the lesson
  6. M11.6

    Reveal the other side

    The interposer on a carrier, ground to its vias, revealed, bumped and released.

    Start the lesson
  7. M11.7

    Hybrid bonding

    Below about 10 µm pitch, copper and oxide bonded directly, without solder.

    Start the lesson
  8. M11.8

    The accelerator

    Onto the substrate, lid and balls; warpage; system-level test; on to the rack.

    Start the lesson
  9. M11 ✎

    Assemble the accelerator

    An interposer, HBM stacks round a logic die and an underfill, against yield, warp and bandwidth; then two failed parts to explain with X-ray and ultrasound. Three missions, then your own build.

    Open the interactive
  10. M11 ✓

    Module check

    Ten questions across the module's eight lessons, eight to pass; then practise its exam scenarios.

    Take the check
M13

The industry

Who makes chips, who pays for them, and who decides where they are made?
  1. M13.1

    Who makes chips

    The chain from research to package; IDMs, fabless firms, foundries and OSATs; why the foundry model began.

    Start the lesson
  2. M13.2

    What a fab costs

    A fab's price; depreciation and the price of a wafer; why fabs run full; cost per transistor by node.

    Start the lesson
  3. M13.3

    Cycles

    Demand, inventory and capacity that takes years to build; shortages and gluts; why memory swings hardest.

    Start the lesson
  4. M13.4

    Research and the roadmap

    R&D's share of revenue; universities, consortia and the chipmakers; roadmaps; the years from lab to fab.

    Start the lesson
  5. M13.5

    Geography and policy

    Where each step is concentrated; chokepoints; subsidies and export controls; supply shocks.

    Start the lesson
  6. M13.6

    Careers

    The jobs in a fab and around it, what each needs, and how people come to them.

    Start the lesson
  7. M13 ✎

    Price the wafer

    Choose how full a fab runs, the node, or the price, predict the number that matters, and see where each wafer's money goes: three missions, then your own fab.

    Open the interactive
  8. M13 ✓

    Module check

    Ten questions across the module, eight to pass; then practise its exam scenarios.

    Take the check
TRACKS

Company tracks

one company's machines, after the module
  1. M5 →

    The Applied Materials track

    Five of Applied's machines in Fab B: a lesson, a visit, a task and a check each; the jobs; a mastery test. By SiliconSim, from Applied's public pages.

    Open the track