THE COURSE / M11 PACKAGE AND TEST / M11.5
Chiplets on an interposer
After this lesson you can:
- Say why a big processor became several dies: the reticle's limit and yield against area.
- Explain what a silicon interposer does, and the two sizes of bump on either side of it.
- Follow chip-on-wafer: place, reflow, clean, underfill, pressure cure, compression mould.
Loading the lesson…
Sources
- Y. Han, H. Xu, M. Lu, H. Wang, J. Huang, Y. Wang, Y. Wang, F. Min, Q. Liu, M. Liu and N. Sun, "The Big Chip: Challenge, model and architecture," Fundamental Research 4, 1431–1441 (2024). The largest single die, 858 mm² (26 × 33 mm), set by the reticle and optics; the Poisson model tends to underestimate large chips' yield; the negative binomial model is widely used; a multi-chiplet system's yield set by its chiplets' yields and the bonding yield, which falls as chiplets are added.
- Wikipedia, "Chiplet" (read 3 November 2026). Chiplets combined on an interposer in one package can be made on different processes and nodes, each suited to its function, and tested before assembly, improving the final device's yield; significant advantages in yield and cost, with new thermal challenges.
- K. Tran (SK hynix), "The Era of High Bandwidth Memory," Hot Chips 28 tutorial, August 2016. TSVs through each DRAM die over a base die with the PHY, the TSV area, the DFT test logic and direct-access balls; 1,024 data I/Os from the base die to the host through the interposer, up to 256 GB/s a stack (HBM2, 2 Gb/s a pin); micro-bumps 25 µm across at 55 µm pitch; a molded known-good stacked die, 0.72 mm tall (Gen2); the test flow: wafer test, wafer burn-in, stacking, a logic test through IEEE 1500, hot and cold tests and repair, speed test; after assembly, repair of cells and of TSVs and micro-bumps by lane remapping through IEEE 1500; thermal dummy bumps for heat.
- US 11,901,334 B2 (Micron Technology), "Microelectronic devices including embedded bridge interconnect structures" (2024). A 2.5D package places several dies side by side on a TSV silicon interposer, attached by micro-bumps about 10 µm across; the interposer is attached to the package substrate by C4 bumps about 100 µm across.
- TSMC, "TSMC and Broadcom Enhance the CoWoS Platform with World's First 2X Reticle Size Interposer" (press release, 3 March 2020, as carried by Design & Reuse). Chip-on-Wafer-on-Substrate, first introduced in 2012; an interposer of about 1,700 mm², twice the reticle, by a mask-stitching process; several logic dies and up to six HBM cubes, 96 GB; up to 2.7 TB/s, 2.7 times its 2016 CoWoS; ready for N5.
- ASMPT AMICRA, NOVA Pro die bonder and flip chip bonder (product page, read 3 November 2026). Placement to ±1.0 µm at 3σ with a cycle under 3 s, by dynamic alignment and laser heating of the substrate; chip on chip, chip on wafer, chip on substrate; often thermocompression bonding; 300 mm wafers.
- Wikipedia, "Flip chip" (read 3 November 2026). Solder bumps deposited on the chip pads in the last wafer step; the chip flipped face down, aligned to the matching pads, and the solder reflowed: controlled collapse chip connection, C4, brought to market by IBM in the 1960s; the short connections greatly reduce inductance and conduct heat better; the underfill distributes the thermal expansion mismatch between chip and board, preventing stress concentration in the joints.
- Heller Industries, Pressure Cure Oven system overview (brochure, read 3 November 2026). A pressure cure oven, or autoclave, minimises voiding and increases adhesion in die attach and underfill: air pressurised in a rigid vessel, heated and cooled by forced convection; 1 to 10 bar, 60 to 200 °C; generally 120 minutes; about 24 magazines.
- TOWA, Molding equipment (product pages, read 3 November 2026). In compression moulding the chips are immersed in a flowable resin in advance, which is then cured: virtually free of resin flow, holding down the pressure on the chips, for thin chips, narrow pitch, long wires and low-k; the CPM1080 moulds wafers up to 300 mm and panels up to 320 x 320 mm, with liquid or granular resin.